iTaste MVP3.0 Pro Full Kit with Tank Atomizer

$99.99 USD

Availability: In Stock

Product Introduction 60W Innokin iTaste MVP3.0 Pro VV/VW Starter Kit with 4.5ml iSub Tank is the newest highly powered vaporizer. With perfect size and clean lines, the 4500mAh mod also provides......

Ecigar


Price Drop Alert

Product Introduction

60W Innokin iTaste MVP3.0 Pro VV/VW Starter Kit with 4.5ml iSub Tank is the newest highly powered vaporizer. With perfect size and clean lines, the 4500mAh mod also provides perfect flavors and unbelievable huge clouds working with Innokin iSub tank.

Parameters of MVP3.0 Pro MOD

Operating Voltage: 3.0V - 9.0V

Operating Wattage: 6.0W - 60W

Battery Capacity: 4500mAh

Operating Resistance: 0.2ohm - 0.5ohm

Charger Port: Micro USB

Parameters of iSub Tank Cartomizer

Material: Stainless Steel + Pyrex Glass + Japanese Organic Cotton

Capacity: 4.5ml

Airflow Adjustable

Resistance: 0.5ohm

Recommended Wattage: 20W - 35W

 

 

It comes with

  • 1 x 60W Innokin iTaste MVP3.0 Pro VV/VW MOD
  • 1 x iSub G Tank Cartomizer
  • 1 x 510-eGo Adapter
  • 1 x USB Cable
  • 1 x iSub G Tank Manual
  • 1 x MPV3.0 Pro Manual
  • 1x Innokin Sticker

Simple packing. Customary packing from the factory, the packing is subject to change without notice.

Features

1. 15 seconds cut-off

2. Flip OLED Screen Orientation

3. Low Voltage Warning

4. Short Circuit/ Atomizer Protection

5. Overheat Protection

6. Over-discharge Protection

7. Pass-through Function

8. Remembers Last Voltage or Wattage setting

9. Portable power source for electronic products

10. No-Spill Coil Swap System

How To Use the MOD

1. Press "Power Button" three times to show on the device.

2. The LED lightweight on the prime can blink to show the present battery level. Green indicates the battery is virtually totally charged. The LED lightweight can power off once it's totally charged. Yellow means around [*fr1] power left, while Red means that low power, you need to urge the device charged.

3. When the power button is ironed, the OLED screen will show the hooked up atomiser resistance, voltage, wattage and remaining battery level.

4. Hold on both "+" and "-" buttons at the same time, the screen will display: resistance of atomiser, battery voltage, puffs taken since the device was last turned off and the last set voltage or wattage.

5. Press both "+" and power button to enter variable electrical power mode. Click "+" or "-" to adjust the electrical power by zero.1 wattage.

6. Press both "-" and power button to enter variable voltage. Click "+" or "-" to adjust the voltage by zero.1 voltage.

 

 

How to Fill the Cartomizer

1. rigorously unscrew the metal section.

2. Add e-liquid against the within wall of the tank.

3. rigorously and firmly tighten. don't fill up.

4. Prepare coils by adding 2-3 drops e-juice to the middle wicks. Wait one minute before vaping.



How to Replace Coils

1. Unscrew the highest section of the metal cap.

2. Gently hold and pull the coil out.

3. Align the flat sides of a brand new coil.

4. Push and insert the new coil to tank.

5. rigorously and firmly tighten the metal cap.


 

  • There is CE mark on the package.
  • No e-juice included. You have to buy it here.
  • Replacement coils is available.

 

 

 

Guarantee 3 months

 

We Also Recommend